search »
» About us
» Integrated Solutions
» Sensor
» Switches
» Process Products
» VIP Access
» Document Download

Get Adobe Acrobat Reader
In order to view PDF documents, you need Adobe Acrobat Reader version 4.0 or later, available for free download from Adobe Systems (click icon to access the web site).
 
• High Function and High Performance Fiber Optic Photoelectric Sensors
Features

• Selection possible for standard, high speed and long distance/ high resolution with the mode switchover.
-  Standard mode (response speed 1ms)
-  High speed mode (response speed 120ms)
-  Long distance/ high resolution mode (scanning distance 1,400mm for use of a standard fiber)
• Stabilization degree (margin) of light receiving by 3-digit digital display: Incoming light level and detecting margin display
• Easy setting by a dial switch
• 4-kind sensitivity and 3-kind workless tuning (BGS and reference sensitivity and percent tuning)
• Optical axis adjustment mode indicating light quality at adjustment in 0 to100 digits.
• One-shot output (The same output timing can be set despite of different target sizes.)
• Prevention of sensor damage for all miswirings
• Remote tuning function enables easy designing and correction of light quantity decrement. (Function for HPX-NT3 and HPX-NT4 only)
 
• Performance
Catalog listing HPX-NT1, HPX-NT3 HPX-NTB1, HPX-NTB3 HPX-NT2, HPX-NT4 HPX-NTB2, HPX-NTB4
Power supply 12 to 24Vdc &10% (ripple 10% P-P max.)
Power consumption 750mW max. (current consumption 30mA at power supply voltage 24Vdc)
Detection target Non-transparent object of more than 1m mdia.(useing HPF-T003)
Standard detection target White paper (useing HPF-D002)
Hysteresis 20% max. (at rated scanning distance)
Oparation mode Light ON/dark ON changeover (Setting by L-ON/D-ON changeover switch)
Output mode N-MOS FET open drain output P-MOS FET open drain output
Control output Switching current: 100mA max. (resistive load), Output dielectric strength: 26.4V, Voltage drop: 2V max. (at switching current 100mA), With power short-circuit protection circuit
Response time Standard 1ms max. for both operation and recovery
Ultra long distance 5ms max. for both operation and recovery
High speed response 120 s max. for both operation and recovery
Remote tuning Available for HPX-NT3 Available for HPX-NT4
Timer Delay Adjustable ON/OFF delay (1ms to 1s: 1ms to 200ms by 1ms step, 200ms to 1s by 100ms step)
One-shot Adjustable one-shot/OFF timer (1ms to 1s: 1ms to 200ms by 1ms step, 200ms to 1s by 100ms step)
Light emitter Red LED Blue LED Red LED Blue LED
Indicating function Incoming light level, setting status, operation indicator, mode indication (RUN, SET, TMR and ADJ)
Ambient light immunity Incandescent lamp: 3,000lx max., Sunlight: 10,000lx max.
Operating temperature -20 to +55°C (Note)
Storage temperature -40 to +70°C
Ambient humidity 35 to 85%RH (non-condensation)
Insulation resistance 20M min. (at 500Vdc)
Dielectric strength 1,000Vac 50/60Hz for one minute between electrically active metals and casing
Vibration resistance 10 to 55Hz, 1.5mm peak-to-peak amplitude, for 2 hours in each of X, Y and Z directions
Shock resistance 500ms2 ,3times in eachof X,Y and Z directions
Weight Approx. 65g (body only with 2m cable)
Circuit protection Output is disabled during Power On (approx. 200ms), Output reverse connection protection circuit
Installation Instructions No.: CP-UM-5210E
Note. Operating temperature range depends on the number of gang-mounted units.
[1 to 2 units: -20 to +55°C, 3 units: -20 to +50°C, 4 to 5 units: -20 to +45°C, 6 units: -20 to +40°C]
Do not apply gang-mounting method if the operating temperature becomes higher than the above-listed temperature.
   
 
 

Address: 3323 Kifer Rd.; Santa Clara, CA; 95051 Phone: 1-866-SENSOR1 Fax: 1-602-216-8211
---------------------------------------------------------------------------------------------------------------------------------------------------------
Yamatake Sensing Control, Limited. © Copyright 2007 Terms and Conditions | Privacy Policy
Powered by: Lan Services